Mold Remediation & Co.
Cleaning · 6 min read

How to get rid of mold in the shower (and keep it gone)

Last reviewed · Based on EPA and CDC guidance · Editorial policy

Quick answer

Scrub tile and grout with detergent and water, then dry the shower completely. Cut out caulk with mold growing under it and re-caulk only once the joint is clean and dry, because the EPA says not to caulk over mold. Then run the exhaust fan during and after every shower so the room dries out.

A white bathtub with a shower curtain in a bathroom
Photo: Alexander Fife on Unsplash

Why showers grow mold

Showers get wet every day, and grout, caulk and shower curtains stay damp longest. The EPA lists running exhaust fans or opening windows when showering as a basic way to control moisture. Without that, the room never fully dries between showers and mold returns within weeks.

What you need

  • Dish detergent or a bathroom cleaner, and warm water
  • A stiff nylon brush or old toothbrush for grout
  • Rubber gloves and eye protection
  • A utility knife or caulk remover, plus mold-resistant silicone caulk (if the caulk is stained)
  • Towels or a squeegee to dry surfaces afterwards

Step by step

  • Ventilate. Turn on the exhaust fan and open a window or door.
  • Scrub tile and grout. Use detergent and water, and work the brush into the grout lines. The EPA recommends detergent and water for mold on hard surfaces.
  • Rinse and dry. Rinse, then dry the walls, tub and grout. Drying is part of the cleaning, not an extra step.
  • Check the caulk. If black spots remain under the surface of the caulk, scrubbing won't reach them. Cut the old caulk out, clean the joint, let it dry fully (ideally overnight) and apply new caulk. The EPA says not to paint or caulk moldy surfaces: clean and dry them first.
  • Wash or replace the curtain and liner. Many fabric curtains and liners can go in the washing machine. Check the care label.
  • Treat stubborn hard-surface stains, if needed. If you choose bleach, the CDC's limit is 1 cup per gallon of water. Ventilate and never mix it with ammonia-based cleaners. See does bleach kill mold?

Keep it from coming back

  • Run the exhaust fan during your shower and for a while after. If you don't have one, open a window.
  • Squeegee or towel off walls and glass after showering.
  • Keep the door or curtain open afterwards so the stall can dry.
  • Keep indoor humidity below 60%, ideally 30 to 50%, per the EPA. A $10 to $50 hygrometer tells you where you are. See the best humidity level to prevent mold.
  • Fix drips and leaks quickly.

When it isn't a cleaning problem

Call a professional if you see soft or crumbling grout, loose tiles, stains on the ceiling below the bathroom, or mold on the drywall outside the shower. Those are signs water is getting behind the tile, and mold may be growing inside the wall. See mold behind walls and mold on the ceiling.

Written by the Mold Remediation & Co. editorial team from the primary sources listed below. This article is general information, not medical or legal advice. Read our editorial policy.

Questions

Why does mold keep coming back in my shower?

Usually because the room doesn't dry out between showers, or because mold is growing under the caulk where cleaning can't reach. Replace stained caulk and run the exhaust fan during and after showers.

Can I caulk over moldy caulk?

No. The EPA says not to paint or caulk moldy surfaces. Remove the old caulk, clean and dry the joint, then re-caulk.

Is pink or orange slime in the shower mold?

Pink or orange film in showers is often bacteria rather than mold. It is cleaned the same way: scrub with detergent, rinse and dry.

Sources

Find mold remediation pros by state

Get it handled properly, the first time.

Compare verified mold remediation pros near you in under a minute.

Find a contractor I'm a contractor